Manuella Lange 

You can use the embedded content settings in the XLIFF Filetype.  You need to do this BEFORE you create your project and just create a single placeholder rule with an expression like this:

{[^}]+}

Hi Paul,

Thanks for your response but I am not very familiar with Regex rules. Do I need to create the rule as you have indicated {[^]+} or to mention each of the tags for ex. {<1 in between the brackets[.. ]. AND do I need to do it before EACH project or is it enough to go to options>Files type>Xliff>Embedded content and to do it for once and for all?

Manuella Lange 

Manuella Lange said:

Do I need to create the rule as you have indicated {[^]+} or to mention each of the tags for ex. {<1 in between the brackets[.. ].

As I indicated.  If all of your codes follow the same pattern as you have shown here then the regex I gave you will catch them all.  However, as I was writing the explanation for you I realised I didn't do this correctly.  That regex would have captured the entire string:

{1> SENTENCE.<1}

I read it too quickly and didn't notice you probably meant this to be a representation of something like this:

{1> This is some text that needs to be translated.<1}

{1> Here's some more translatable text.<1}

{/b> Here's some bold text.<\b}

It definitely helps to provide a proper snippet of code when you want help so it's 100% clear what your needs are.  However, there is another reason why a snippet is very important.  Tags like these are going to be invalid in XLIFF unless they are written in CDATA or use compliant tags.

So, before I try to explain how to do this properly (the regex is the easy bit) can you provide a small snippet of the actual file?  Should be easy to replace the translatable text for a few lines with something that won't break an NDA.  Is it something like this:

<trans-unit id="1">
<source><ph id="1">{1&gt;</ph> This is some text that needs to be translated.<ph id="2">&lt;1}</ph></source>
<target><ph id="1">{1&gt;</ph> This is some text that needs to be translated.<ph id="2">&lt;1}</ph></target>
</trans-unit>

Or this:

<trans-unit id="1">
<source><![CDATA[{1> This is some text that needs to be translated. <1}]]></source>
<target><![CDATA[{1> This is some text that needs to be translated. <1} ]]></target>
</trans-unit>

for example?  Or something else altogether?

If you can share a complete file it's even better, but this much at least would help provide you a better answer.

Here is an example of a source file. I have send the file via e-mail to your adress @sdl.com.

Leadership is {u>not<u} a position or title.
Leadership is {u>not<u} seniority in an organization.

{b>Program Objectives <b}(continued)

{i>www.businessdictionary.com<i}

 Manuella Lange 

Thanks for the file.  If you had opened it with a text editor to check what the filetype was so you could determine how to handle it you would have seen this:

xmlns:m="www.memsource.com/.../2.0"

This is telling you that the file comes from Memsource, or Phrase as they're called today.  In Studio we have an XLIFF filetype specifically for this customised version of XLIFF.  If you use this filetype you will see this:

For some reason the filetype extension has been changed to XLIFF, when it was probably MXLIFF originally.  However, if you either change it to *.mxliff, or add *.xliff to the  "File dialog wildcard expression:" then you'll be able to use it:

If you decide to add *.xliff to the memource filetype rather than rename the extension then make sure you also uncheck the vanilla XLIFF filetype above the memsource filetype before creating your project.  If you don't the XLIFF filetype will continue to be used:

Thank you so much Paul

Paul 

Hello Paul,

I have a similar issue and despite reading your advice carefully here (and here), I'm still unable to sort out my issue.

This is what I see in Phrase

and this is what I get in Studio 

I've used this rule you suggested, as it seemed to also make sense in my case. But maybe it does not! I must say I'm really not an export in Regex...

Any clue how I can sort this out?

Aubeline Brandamir 

Would make a lot more sense to create a new thread for this problem.  Then you can also provide the information we need to help you resolve this:

1. You showed Phrase... so I guess it's an *.mxliff file?
2. If it's not then which XLIFF filetype are you using to handle the file?  You made the changes in the XLIFF presumably because that's what you saw in the other threads.  But perhaps this isn't correct for your file?
3. What version of Trados Studio?

Aubeline Brandamir 

Would make a lot more sense to create a new thread for this problem.  Then you can also provide the information we need to help you resolve this:

1. You showed Phrase... so I guess it's an *.mxliff file?
2. If it's not then which XLIFF filetype are you using to handle the file?  You made the changes in the XLIFF presumably because that's what you saw in the other threads.  But perhaps this isn't correct for your file?
3. What version of Trados Studio?

Hi Paul 

New thread here